Evaluation of the Effectiveness of Disinfectants on Impression Materials.

Background The disinfection of dental impression materials is a cornerstone of infection control in dental practice. This study aimed to evaluate the effectiveness of two disinfectants, sodium hypochlorite and iodophor, on alginate and silicone impression materials, which are prone to microbial contamination. Methods The study was structured into two main groups based on the impression material: Group I (alginate) and Group II (addition silicone), each further subdivided into two subgroups for disinfection with sodium hypochlorite and iodophor. For each subgroup, initial microbial swabs were taken before any treatment, followed by a second swab after rinsing and a final swab after disinfection. The mean colony-forming unit (CFU) counts, standard deviations, and standard errors of the mean were calculated for each stage of treatment. Results Prior to disinfection, Group I had a mean CFU count of 2,529.40, while Group II had a lower mean CFU of 1,417.40. After rinsing, there was a significant decrease in CFUs in both groups, with Group I at 1,337.10 and Group II at 415.10. Post-disinfection, Group I showed a mean CFU count of 73.00 for sodium hypochlorite and 0.00 for iodophor. Similarly, Group II achieved a CFU reduction of 99.00 with sodium hypochlorite and 0.00 with iodophor, demonstrating a marked reduction in microbial presence. Conclusion Iodophor was exceptionally effective in disinfecting both alginate and silicone impression materials, eliminating all detectable CFUs. Sodium hypochlorite also significantly reduced microbial counts but was not as effective as iodophor. Rinsing prior to disinfection was instrumental in reducing the microbial load, underscoring its importance in the disinfection protocol.

Disinfection efficacy of sodium hypochlorite and glutaraldehyde and their effects on the dimensional stability and surface properties of dental impressions: a systematic review.

Objective: To systematically evaluate the disinfection efficacy of the two most frequently used disinfectants, sodium hypochlorite and glutaraldehyde, and their effects on the surface properties of four different dental impression materials. Methods: A systematic literature search was performed in four databases until May 1st, 2022 to select the studies which evaluated disinfection efficacy of disinfectants or surface properties of dental impressions after chemical disinfection. Main results: A total of 50 studies were included through electronic database searches. Of these studies, 13 studies evaluated disinfection efficacy of two disinfectants, and 39 studies evaluated their effects on the surface properties of dental impressions. A 10-minute disinfection with 0.5-1% sodium hypochlorite or 2% glutaraldehyde was effective to inactivate oral flora and common oral pathogenic bacteria. With regard to surface properties, chemical disinfection within 30 min could not alter the dimensional stability, detail reproduction and wettability of alginate and polyether impressions. However, the wettability of addition silicone impressions and the dimensional stability of condensation silicone impressions were adversely affected after chemical disinfection, while other surface properties of these two dental impressions were out of significant influence. Conclusions: Alginate impressions are strongly recommended to be disinfected with 0.5% sodium hypochlorite using spray disinfection method for 10 min. Meanwhile, elastomeric impressions are strongly recommended to be disinfected with 0.5% sodium hypochlorite or 2% glutaraldehyde using immersion disinfection method for 10 min, however, polyether impression should be disinfected with 2% glutaraldehyde.

Viabilidade do escaneamento intraoral no ensino superior em Odontologia em uma universidade pública / Viability of intraoral scanning in dentistry teaching at a public university

O ensino do fluxo digital com escâners na pós-graduação e especialização já é consagrado, mas existe uma lacuna em sua utilização no ensino da graduação. O objetivo deste estudo foi avaliar a viabilidade do escaneamento intraoral no ensino superior em odontologia em uma universidade pública moldagem, através de três diferentes perspectivas: o professor do curso de graduação, o aluno de graduação e o paciente submetido ao procedimento. Foram desenvolvidos e aplicados três questionários distintos aos participantes voluntários, 25 pacientes responderam 18 questões, 27 alunos responderam 7 perguntas e 11 professores responderam 8 questões. Para análise estatística foi realizado o teste de correlação de Pearson entre as percepções nas variáveis envolvendo cada um dos procedimentos, e também foi realizado o teste T (p <0,05). Foi encontrada correlação estatística entrenáusea e tempo de procedimento, e também entre náusea e gosto do material de moldagem. Os resultados descritivos mostraram que os pacientes apresentaram idade variada (7 anos a 73 anos), preferência pelo escaneamento, no procedimento como um todo, tamanho da peça em boca, registro oclusal, tempo clínico, gosto e náusea. Os alunos possuíam idade entre 21 e 31 anos, sendo que 85% precisaram repetir a moldagem e 19 se sentiram parcialmente confortáveis ao moldar. A idade dos professores variou entre 30 e 59 anos. Todos os professores precisaram intervir na moldagem e 81% acreditam que os alunos conseguiram finalizar bem o procedimento. Todos os alunos e professores avaliaram como importante a inserção do escaneamento na graduação. Em relação aos custos da Universidade, o escaneamento demonstrou ter o menor custo devido à quantidade de repetições realizadas na clínica de graduação. A inovação do projeto foi a possibilidade de se comparar custos, conforto e tempo clínico, promovendo impacto em ambientes multidisciplinares e na universidade. Conclui-se que para o paciente o escaneamento foi melhor que a moldagem, e para os alunos e professores, é importante o ensino de novas tecnologias na graduação (AU)

The teaching of digital flow with scanners in postgraduate and specialization courses is already well-established, but there is a gap in its use in undergraduate teaching. The aim of this study was to assess the feasibility of intraoral scanning in undergraduate dental education at a public university, from three different perspectives: the undergraduate teacher, the undergraduate student and the patient who underwent the procedure. Three different questionnaires were developed and applied to the volunteer participants: 25 patients answered 18 questions, 27 students answered 7 questions and 11 teachers answered 8 questions. For statistical analysis, Pearson's correlation test was carried out between the perceptions of the variables involving each of the procedures, and the T-test was also carried out (p<0.05). A statistical correlation was found between nausea and procedure time, and also between nausea and the taste of the impression material. The descriptive results showed that the patients varied in age (7 years to 73 years), preference for scanning, the procedure as a whole, mouthpiece size, occlusal registration, clinical time, taste and nausea. The students ranged in age from 21 to 31, 85% had to repeat the impression and 19 felt partially comfortable taking the impression. The teachers' ages ranged from 30 to 59. All the teachers had to intervene in the molding and 81% believed that the students were able to finish the procedure well. All the students and teachers considered the introduction of scanning in the undergraduate program to be important. In terms of the university's costs, scanning proved to be the least expensive due to the number of repetitions carried out in the undergraduate clinic. The innovation of the project was the possibility of comparing costs, comfort and clinical time, promoting impact in multidisciplinary environments and at the university. The conclusion is that scanning was better for the patient than impression taking, and for students and teachers, it is important to teach new technologies in undergraduate courses (AU)

Application of polyetheretherketone (PEEK) posts: evaluation of fracture resistance and stress distribution in the root: in vitro and finite element analyses

Abstract To evaluate the feasibility of using a milled polyetheretherketone (PEEK) post and core in endodontically treated teeth with or without a ferrule. Sixty bovine tooth roots were endodontically treated followed by cementation of intraradicular retainers (IR), according to each experimental group: a) non-ferrule glass fiber post (f0FP); b) 2-mm-ferrule glass fiber post (f2FP); c) non-ferrule resized glass fiber post (f0PR); d) 2-mm-ferrule resized glass fiber post (f2PR); e) non-ferrule PEEK post and core (f0PPC); and f) 2-mm-ferrule PEEK post and core (f2PPC). Metal crowns were made and cemented. A periodontal ligament was simulated using polyether. A force was applied to the palatine portion of each sample at 45°, until fracture. Fracture resistance data were submitted to two-way ANOVA and Tukey's test (α = 0.05). Three-dimensional digital models were developed to calculate the tensions formed in the root using finite element analysis. Models of glass fiber posts and PEEK posts and cores were evaluated with or without a ferrule. The results were analyzed by the Mohr-Coulomb criterion. The type of IR was not influenced by fracture strength (p = 0.243). There were significant statistical differences among the remaining factors. Ferrule groups had greater fracture resistance, and the failure mode of teeth with a ferrule was more catastrophic than the non-ferrule group. A ferrule increases fracture resistance and influences failure mode; the PEEK post and core did not modify the biomechanics of endodontically treated teeth, and resembled the glass fiber post results. The crack initiation point differed between the ferrule and non-ferrule groups.

The Potential of Digital Impression in Orthodontics.

BACKGROUND: Over the past 20 years, there have been many innovations in orthodontic diagnosis and therapy. Among the innovations, there is the taking of dental impressions (DIs). Dental impressions are the negative imprint of hard and soft tissues of one or both arches, and they allow a plaster model to be formed, i.e., a positive reproduction. Traditional dental impressions can be made of different materials, such as alginate, while digital impression is captured by an intra-oral scanner. Digital impression, despite the evident advantages, has not yet replaced the conventional impression. The aim of this study is to evaluate which dental impressions are the most used by dentists. For this purpose, we considered 120 questionnaires sent electronically to patients of different dental private practices from different countries, where the dentists can use both techniques. The results highlighted that the kind of impression adopted is very much influenced by the type of therapy and orthodontic devices used in the treatment. We can conclude that, despite the advent of digital technology, conventional impressions are still used for fixed devices, while digital impressions are more adopted for orthodontic customized devices and therapies with clear aligners, that are very widespread among adult patients.

The Influence of a Flexible Model on the Marginal Adaptation of Inlay Composite Restorations: A MicroCT Analysis.

The aim of this study was to evaluate the influence of flexible models on the marginal adaptation of indirect resin composite restorations. Thirty-six cavity preparations were made for class II restorations in permanent molar teeth. Three groups (n=12) were defined following three impressions/model material combinations: G(STONE), polyvinylsiloxane, and type IV stone model, as a control group; G(IMPRESSIONPVS), alginate and flexible polyvinylsiloxane; G(MODELPVS), alginate and flexible polyvinylsiloxane for models. All restorations were positioned on their respective teeth and evaluated by micro-computed tomography. Absolute marginal discrepancies were measured digitally (ImageJ). The results were compared using one-way ANOVA (p⟨ 0.05). The mean ± SD absolute marginal discrepancy of indirect resin composite restorations made from flexible and rigid stone models was as follows: G(STONE), 206 (±79.95) µm; G(IMPRESSIONPVS), 221.50 (±61.73) µm; G(MODELPVS), 203.25 (±65.93) µm. Absolute marginal discrepancies were not significantly influenced by the flexible and rigid stone models (p=0.78). The flexible or rigid stone model did not influence the marginal adaptation of the indirect resin composite restorations.

Evaluation of Elastomeric Impression Materials' Hydrophilicity: An in vitro Study.

INTRODUCTION: Hydrophilicity of dental impression materials is crucial for obtaining an accurate impression and necessary for the production of a well-fitting cast restoration. The most common technique for evaluation of hydrophilicity is a contact angle measurement. The aim of the present in vitro study was to compare the water contact angles of four groups of elastomeric impression materials, before and during setting. MATERIAL AND METHODS: Flattened specimens (n=10) of tested impression materials were prepared by the use of a Teflon mold with specific dimensions. A 5µl droplet of deionized water fell on the specimen, and photos were taken using a Nikon D3200 DSLR camera and a 105 mm macro lens (Nikorr, Nikon) in specific time points. RESULTS: The CAD/CAM material showed the highest contact angle measurements. The light body polyvinylsiloxane (PVS) material 1, polyether and vinylsiloxanether material showed comparable contact angle measurements especially at the initial time point. A statistically significant reduction of contact angles was reported during setup time for all PVS, PE and vinylsiloxanether materials, while the most expressed reduction of contact angle measurements, and thus the most significant increase of hydrophilicity were reported for light wash PVS material 2. CONCLUSIONS: The CAD/CAM impression material showed the most hydrophobic behavior. PVS materials showed excellent hydrophilicity. Polyether and polyvinyloxanether impression materials presented lower contact angle measurements, and thus superior hydrophilicity, compared with other tested materials initially and during setting. All tested impression materials presented a stepwise development of hydrophilicity during the setting stage.

Improved water absorption behaviour of experimental hydrophilic vinyl polysiloxane (VPS) impression materials incorporating a crosslinking agent and a novel surfactant.

OBJECTIVES: To study the effects of incorporating a further crosslinking agent and a novel surfactant on the water absorption behaviour of experimental VPS impression materials. METHODS: Part 1: The water uptake behaviour of Aquasil-Ultra-Monophase (AqM) was studied gravimetrically in three media (DW, 1%NaOCl and Perform ID), at 23 °C and 37 °C, over a period of one and four-months (n = 5) to gain information on long-term immersion. Part 2: Five experimental materials were formulated: Exp-I and II as hydrophobic and Exp-III-V as hydrophilic, containing an additional cross-linking agent (TFDMSOS) and Rhodasurf CET-2 surfactant. Their water uptake and desorption (both at 23 °C) properties (gravemetrically), solubility, pH and diffusion coefficient (DC) data were compared with three commercial, hydrophilic VPS impression materials, over seven days (n = 5). The results were analysed statistically. RESULTS: Part 1: Significant differences in water absorbed by AqM were observed in the three media at 23 °C. Aq M had a significantly higher uptake in 2% Perform ID, than in DW and NaOCl. At 37 °C, over four-months the uptake profiles were more enhanced and differed. Part 2: All Exp and commercial materials significantly increased in weight in both media (DW and 1% NaOCl at 23 °C), with differing uptake profiles and non-reached equilibrium. Exp-VPS absorbed significantly less water than commercial-VPS. Desorption of all VPS from both parts was faster than absorption, followed Fickian diffusion kinetics and reached equilibrium within 1-3 days. Desorption DCs for Exp-VPS were higher than commercial materials (10-10 versus 10-11 m2 s-1). The solubility was higher in 1% NaOCl compared to DW. The pH of DW after immersion of samples significantly increased compared to 1% NaOCl. SIGNIFICANCE: The incorporation of novel cross-linking agent, TFDMSOS and non-ionic surfactant, Rhodasurf CET-2, (ethoxylated-cetyl-oleyl alcohol) improved the dimensional stability of hydrophilic Exp-VPS in DW and 1% NaOCl. These materials merit further research in producing accurate casts of the patient's anatomy following disinfection.

Evaluation of Gingival Displacement with Aluminum Chloride and Naphazoline Hydrochloride: A Randomized Controlled Trial.

The objective of this study was to evaluate the use of naphazoline hydrochloride in comparison with aluminum chloride for vertical gingival displacement. The inclusion criteria were: patients with a good general systemic condition; periodontal health; and thick gingival biotype. Moreover, the exclusion criteria were: smoking individuals; canine teeth or central incisors with carious lesions, abrasion, erosion, prosthetic abutments or unsatisfactory restorations; patients with periodontal disease; and users of continuous medication. 72 teeth were included and the Square Block Design was used to randomize the samples. Three measures were obtained from each tooth, and mean vertical gingival displacement was calculated. A descriptive analysis of the average displacement was performed. The normality test used was the Lilliefors' Test and for comparison between treatments, the Kruskal-Wallis Test was used. The Bartlett's Test for homogeneity of variances was used and a 5% (p ⟨ 0.05) significant level was considered. Thus, the Aluminum Chloride and Naphazoline Hydrochloride showed no statistically amount of gingival retraction than the control group (p = 0.3822). The average of gingival vertical displacement in all groups were less than 0,5 mm. The technique used did not allow any amount of horizontal displacement on obtained models.

Optimization of antimicrobial efficiency of silver nanoparticles against three oral microorganisms in irreversible hydrocolloid impressions.

BACKGROUND AND OBJECTIVES: Silver nanoparticles (Ag-NPs) are potent antimicrobial agents, which have recently been used in dentistry. The aim of the current study was to optimize antimicrobial activity of Ag-NPs used in preparing irreversible hydrocolloid impressions against three microorganisms of Escherichia coli, Streptococcus mutans and Candida albicans. MATERIALS AND METHODS: After assessing antimicrobial activity of the compound using disk diffusion method, three parameters of concentration of Ag-NPs (250-1000 ppm), ratio of hydrocolloid impression material powder to water (0.30-0.50) and time of mixing (20.0-60.0 s), affecting antimicrobial activity of irreversible hydrocolloid impression materials against the three microorganisms, were optimized. This combined process was successfully modeled and optimized using Box-Behnken design with response surface methodology (RSM). Decreases in colony number of E. coli, S. mutans and C. albicans were proposed as responses. RESULTS: Qualitative antimicrobial assessments respectively showed average zone of inhibition (ZOI) of 3.7 mm for E. coli, 3.5 mm for S. mutans and 4 mm for C. albicans. For all responses, when the mixing duration and powder-to-water ratio increased, the circumstances (mixing duration of 59.38 s, powder-to-water ratio of 0.4 and Ag-NP concentration of 992 response) increased. Results showed that in optimum ppm, the proportion of decreases in colony numbers was maximum (89.03% for E. coli, 87.08% for S. mutans and 74.54% for C. albicans). Regression analysis illustrated a good fit of the experimental data to the predicted model as high correlation coefficients validated that the predicted model was well fitted with data. Values of R2Adj with R2Pred were associated to the accuracy of this model in all responses. CONCLUSION: Disinfection efficiency dramatically increased with increasing of Ag-NP concentration, powder-to-water ratio and mixing time.

Extended-pour and conventional alginates: effect of storage time on dimensional accuracy and maintenance of details

ABSTRACT Objective: This study aimed to evaluate the dimensional stability and maintenance of details of conventional and high stability alginates up to 5-day storage. Methods: Two types of alginates were selected (n=10) for this study, conventional (Hydrogum) and high stability alginates (Hydrogum 5), which were produced with the aid of a cylindrical metal block and a ring-shaped metal mold (Specifications 18, 19, and 25, ANSI/ADA). Ten images were obtained from the molds for the dimensional stability test, which were taken immediately after their production and at each different storage periods (15 min, 24 h, 48 h, 72 h, 96 h, and 120 h) by a digital camera. The specimens were kept hermetically sealed in plastic bags (23°C) and then used to obtain 140 (n=70) dental stone models, used in the detail reproduction test, in which the angular accuracy of three grooves (20 µm, 50 µm, and 75 µm) was observed at each period. The details reproduction accuracy was classified using a predetermined score classification. Measurements of dimensional changes were made in the Corel DRAW X6 program. The data were submitted to the Student's t-test (α?#8197;= 0.05). Results: A statistically significant difference concerning the size of the matrix was observed after 24h for both alginates, and a statistically significant negative linear dimensional change (contraction) was verified after 24 h of storage (1.52% for the high stability alginate, and 1.32% for the conventional alginate). The high stability alginate kept the full details for 72 hours, while the conventional alginate, for 24 h. Both alginates reproduced the 75 µm groove at all storage periods. Conclusion: Impressions made with both alginates presented satisfactory clinical results when the alginates were immediately poured.

RESUMO Objetivo: O presente estudo teve como objetivo avaliar a estabilidade dimensional e manutenção de detalhes de alginatos convencionais e de alta estabilidade por até 5 dias de armazenamento. Métodos: Para esse estudo, foram selecionados dois tipos de alginatos: convencional (Hydrogum) (n = 10) e de alta estabilidade (Hydrogum 5) (n = 10), sendo produzidos com o auxílio de um bloco metálico cilíndrico e um molde metálico em forma de anel (especificações 18, 19 e 25, ANSI/ADA). Para o teste de estabilidade dimensional, dez imagens foram obtidas imediatamente e para cada tempo de armazenamento (15 min, 24, 48, 72, 96 e 120 horas), realizadas por câmera digital. As amostras foram mantidas hermeticamente fechadas em sacos plásticos (23°C). Para o teste de reprodução de detalhes, as amostras foram utilizadas para obter 140 (n = 70 por grupo) modelos de gesso, sendo observada a precisão angular de três sulcos (20 µm, 50 µm e 75 µm) para cada período. A precisão da reprodução de detalhes foi classificada usando uma classificação de pontuação predeterminada. As medições das mudanças dimensionais foram feitas no programa Corel DRAW X6. Os dados foram submetidos ao teste t de Student (α = 0,05). Resultados: Foi observada diferença estatística em relação à matriz após 24h para ambos os alginatos. Uma mudança dimensional linear negativa estatisticamente significativa (contração) foi verificada após 24 h de armazenamento (1,52% para alginato de alta estabilidade; 1,32% para alginato convencional). O alginato de alta estabilidade manteve os detalhes completos por até 72 horas, enquanto o alginato convencional, por 24 horas. Os alginatos reproduziram o sulco de 75 µm para todos os períodos. Conclusão: As impressões feitas com ambos os alginatos devem ser imediatamente vazadas para se ter resultados clínicos satisfatórios.

Evaluación de la precisión de impresiones sobre implantes usando guía multifuncional en el sistema all-on-four / Accuracy of implant impression using a multifunctional guide in the All-on-Four treatment concept

ABSTRACT Introduction: The passivity of prosthetic components is one of the most important prerequisites in oral implant rehabilitation for maintenance of osseointegration. Objective: Thus, the present study analyzed in vitro the accuracy of different molding techniques in prosthetic rehabilitation on angled implants installed in an anatomical model of a metallic edentulous maxilla. Methods: Laboratory experiment study. A reference metal model of an edentulous maxilla was used. A metal framework was used for the misadaptation assessment. Three groups (n= 10) were compared and impressions were made with vinyl-polysiloxane and casts were obtained with type IV stone: (1) Impression with a metallic open-tray without splinted transfers; (2) Impression with a metallic open-tray and metal splinted transfers; (3) Impression with a multifunctional guide and metal splinted transfers. Misadaptation was assessed with the aid of a stereomicroscope and measuring software. Data were submitted to ANOVA with Welch correction and the Games-Howell post-hoc test with the significance set at 5 percent. Results: Misadaptation (µm) was 110,23 ± 30,94, 37,53 ± 3,92, and 37,69 ± 2,79 for the the groups. Statistically significant differences between impression with a metallic open-tray with and without splinted transfers were observed (p < 0,001). No significant differences between the other types of impression. Conclusions: Impression with a metallic open-tray without splinted transfers and with a multifunctional guide splinted with metal transfers were the most precise methods resulting in higher accuracy in transferred implants(AU)

RESUMEN Introducción: La pasividad de los componentes protésicos es uno de los prerrequisitos más importantes para el mantenimiento de la osteointegración en la rehabilitación oral sobre implantes. Objetivo: Evaluar in vitro la precisión de diferentes técnicas de impresión en rehabilitación sobre implantes inclinados instalados en un modelo anatómico de un maxilar metálico desdentado. Métodos: Estudio de laboratorio de tipo experimental. Se utilizó un modelo metálico de referencia de un maxilar desdentado. Fue utilizada una barra metálica para la evaluación de la desadaptación. Se compararon tres grupos (n = 10), se realizaron impresiones con polivinilsiloxano y se obtuvieron modelos con yeso piedra tipo IV: (1) impresión con una cubeta metálica abierta sin unión de los transferentes; (2) impresión con una cubeta metálica abierta y unión de los transferentes con cilindros metálicos; (3) impresión con una guía multifuncional y unión de los transferentes con cilindros metálicos. La desadaptación se evaluó con la ayuda de un microscopio estereoscópico y un software de medición. Los datos se enviaron a ANOVA con la corrección de Welch y la prueba post-hoc de Games-Howell con la significación establecida en 5 por ciento. Resultados: La desadaptación (µm) fue de 110,23 ± 30,94; 37,53 ± 3,92 y 37,69 ± 2,79 para los grupos, respectivamente. Se observaron diferencias estadísticamente significativas entre la impresión con cubeta abierta metálica con y sin unión de los transferentes (p <0,001). No hubo diferencias significativas entre los otros tipos de impresiones. Conclusiones: La impresión con cubeta abierta metálica sin unión de los transferentes y con una guía multifuncional con unión de los transferentes con cilindros metálicos fueron los métodos más precisos que dieron como resultado una mayor precisión en la transferencia de la posición de los implantes(AU)

Dimensional stability of alginate molds scanned at different storage times / Estabilidade dimensional de moldes de alginato digitalizados em diferentes tempos de armazenamento

ABSTRACT The aim of this study was to evaluate the precision and accuracy of molds made with four commercial brands of alginate scanned at different times using digital model analysis. Eighty molds of a standard Typodont were made using 4 types of alginate (CCC: Cavex Color Change; IA: Identic Alginate; HY5: Hydrogum 5 and JP: Jeltrate Plus). The molds were scanned at four times: immediately (T1), 24h (T2), 72h (T3) and 120h (T4) after molding. Measurements were taken in three dimensions: anteroposterior, transverse and vertical. Significant differences in dimensional changes were noted between the materials over time (p <0.05). Anteroposterior dimensional variation was noted between times, especially for IA and JP. For transverse and vertical variables, a difference was found between the groups, especially at 24 h, 72 h and 120 h. CCC presented significant dimensional shrinkage only at T120 (transverse). IA and JP presented larger dimensional distortions in the vertical measurements. The molding materials used were not dimensionally stable when evaluated after 120 hours of molding. However, such evidence suggests that alginates with longer storage time, such as Cavex Color Change, are more accurate than conventional alginates.

RESUMO O objetivo do presente estudo foi avaliar a precisao e acurácia por meio de análise de modelos digitais de moldes digitalizados obtidos com quatro marcas comerciais de alginato em diferentes tempos. Oitenta moldes de um Typodont padrao foram obtidos utilizando 4 tipos de alginato (CCC: Cavex Color Change; IA: Identic Alginate; HY5: Hydrogum 5 e JP: Jeltrate Plus). Os moldes foram escaneados em quatro tempos: mediatamente (T1), 24h (T2), 72h (T3) e 120h (T4) após a moldagem. As medidas foram feitas em très dimensoes: ântero-posterior, transversal e vertical. Diferenças significativas nas mudanças dimensionais foram observadas entre os materiais ao longo do tempo (p <0,05). Variação dimensional ântero-posterior foi observada entre os tempos, principalmente para IA e JP. Para as variáveis transversal e vertical houve diferenga entre os grupos, principalmente em 24h, 72h e 120h. CCC apresentou contração dimensional significativa apenas em T120 (transversal). IA e JP apresentaram maiores distorções dimensionais na vertical. Os materiais de moldagem utilizados nao foram dimensionalmente estáveis quando avaliados após 120 horas de moldagem. No entanto, tais evidencias sugerem que os alginatos com maior tempo de armazenamento, como Cavex Color Change, sao mais precisos do que os alginatos convencionais.

A comparative evaluation of three dimensional accuracy of different types of interocclusal recording materials - an in vitro study.

INTRODUCTION: The interocclusal registration materials record the occlusal relationship between the natural and /or artificial teeth for planning an occlusal rehabilitation in removable and fixed partial dentures. AIM AND OBJECTIVES: The aim of this in vitro study was to evaluate and compare the accuracy and the three dimensional stability offered by three different types of interocclusal recording materials at storage time intervals of 1 hour and 24 hours. METHODS: Three commercially available interocclusal recording materials were used: Group I-Polyether bite registration paste (Ramitec), Group II-Polyvinylsiloxane bite registration material (Imprint), Group III-Bite registration wax (Maarc). The test was carried out using an epoxy resin model. A total of 30 samples were made with each group consisting of ten samples. Three dimensional measurements were carried out by using 3D-Coordinate measuring machine (CMM) at time intervals of 0-1 hour and 0-24 hours in X, Y and Z-axis. RESULTS: Twelve readings were obtained for three axes (4 readings for each sample at 1 axis) and the averages of these four values were noted for a particular axis (X/Y/Z). Statistical analysis was performed using analysis of variance (ANOVA) for comparison among the groups and then Tukey's honestly significant difference (HSD) tests was performed for comparison among groups at the 0.05 level of significance. CONCLUSION: Polyvinylsiloxane was dimensionally the most stable material followed by polyether and finally bite registration wax. Dimensional accuracy and stability is influenced by both "material" and "time" factors.

3D Digital Impression Systems Compared with Traditional Techniques in Dentistry: A Recent Data Systematic Review.

The advent of new technologies in the field of medicine and dentistry is giving improvements that lead the clinicians to have materials and procedures able to improve patients' quality of life. In dentistry, the last digital techniques offer a fully digital computerized workflow that does not include the standard multiple traditional phases. The purpose of this study is to evaluate all clinical trials and clinical randomized trials related to the digital or dental impression technique in prosthetic dentistry trying to give the readers global information about advantages and disadvantages of each procedure. Data collection was conducted in the main scientific search engines, including articles from the last 10 years, in order to obtain results that do not concern obsolete impression techniques. Elsevier, Pubmed and Embase have been screened as sources for performing the research. The results data demonstrated how the working time appears to be improved with digital workflow, but without a significant result (P = 0.72596). The papers have been selected following the Population Intervention Comparison Outcome (PICO) question, which is related to the progress on dental impression materials and technique. The comparison between dentists or practitioners with respect to classic impression procedures, and students open to new device and digital techniques seem to be the key factor on the final impression technique choice. Surely, digital techniques will end up supplanting the analogical ones altogether, improving the quality of oral rehabilitations, the economics of dental practice and also the perception by our patients.

Dimensional stability of alginate molds scanned at different storage times.

The aim of this study was to evaluate the precision and accuracy of molds made with four commercial brands of alginate scanned at different times using digital model analysis. Eighty molds of a standard Typodont were made using 4 types of alginate (CCC: Cavex Color Change; IA: Identic Alginate; HY5: Hydrogum 5 and JP: Jeltrate Plus). The molds were scanned at four times: immediately (T1), 24h (T2), 72h (T3) and 120h (T4) after molding. Measurements were taken in three dimensions: anteroposterior, transverse and vertical. Significant differences in dimensional changes were noted between the materials over time (p <0.05). Anteroposterior dimensional variation was noted between times, especially for IA and JP. For transverse and vertical variables, a difference was found between the groups, especially at 24 h, 72 h and 120 h. CCC presented significant dimensional shrinkage only at T120 (transverse). IA and JP presented larger dimensional distortions in the vertical measurements. The molding materials used were not dimensionally stable when evaluated after 120 hours of molding. However, such evidence suggests that alginates with longer storage time, such as Cavex Color Change, are more accurate than conventional alginates.

O objetivo do presente estudo foi avaliar a precisão e acurácia por meio de análise de modelos digitais de moldes digitalizados obtidos com quatro marcas comerciais de alginato em diferentes tempos. Oitenta moldes de um Typodont padrão foram obtidos utilizando 4 tipos de alginato (CCC: Cavex Color Change; IA: Identic Alginate; HY5: Hydrogum 5 e JP: Jeltrate Plus). Os moldes foram escaneados em quatro tempos: imediatamente (T1), 24h (T2), 72h (T3) e 120h (T4) após a moldagem. As medidas foram feitas em três dimensões: ântero-posterior, transversal e vertical. Diferenças significativas nas mudanças dimensionais foram observadas entre os materiais ao longo do tempo (p <0,05). Variação dimensional ântero-posterior foi observada entre os tempos, principalmente para IA e JP. Para as variáveis transversal e vertical houve diferença entre os grupos, principalmente em 24h, 72h e 120h. CCC apresentou contração dimensional significativa apenas em T120 (transversal). IA e JP apresentaram maiores distorções dimensionais na vertical. Os materiais de moldagem utilizados não foram dimensionalmente estáveis quando avaliados após 120 horas de moldagem. No entanto, tais evidências sugerem que os alginatos com maior tempo de armazenamento, como Cavex Color Change, são mais precisos do que os alginatos convencionais.

Avaliação do escoamento de materiais de moldagem elastoméricos através do teste 'Shark-Fin' modificado / Analysis of flow profile of elastomeric impression materials using a modified 'Shark-Fin' Test

Materiais de impressão com boa fluidez são essenciais para a captura das margens dos preparos dentais. O objetivo deste estudo, para tanto, foi avaliar, por meio do dispositivo de teste 'shark-fin' (3M ESPE), o escoamento de dois materiais de moldagem elastoméricos, um poliéter (PE) e um polivinilsiloxano (PVS). Foi realizada uma modificação no teste 'shark-fin' de modo a permitir a aproximação do estudo in vitro à realidade clínica, avaliando o comportamento de duas viscosidades de cada material aplicadas em um tempo único. Um poliéter (PE) de alta (Impregum Penta Soft / 3M ESPE) e de baixa viscosidade (Impregum Garant L Duosoft / 3M ESPE), um polivinilsiloxano (PVS) de alta (Express XT Penta H / 3M ESPE), de média (Express XT Pasta Fluida de Média viscosidade / 3M ESPE) e de baixa viscosidade (Express XT Pasta Fluida de Baixa viscosidade / 3M ESPE) foram divididos em 21 grupos (n=5) e testados isoladamente e combinados em proporções de 1 : 1, nos tempos de trabalho de 50, 80 e 120 s. Após, as alturas das barbatanas formadas foram medidas com o auxílio de um paquímetro digital. A análise estatística dos resultados foi realizada por análise de variância (ANOVA) one-way seguida pelo teste LSD post hoc (p=0,05). Verificou-se que os valores das alturas das barbatanas diferiram significativamente entre os materiais e a cada intervalo de tempo (p<0,05). As barbatanas diminuíram para todos os grupos com o aumento do tempo de trabalho, exceto para o grupo PE de baixa viscosidade e PVS em múltiplas misturas (alta associada à baixa viscosidade e alta associada à média viscosidade). Todos os grupos de PE apresentaram valores mais altos para as barbatanas formadas em comparação aos grupos de PVS, tanto em uma viscosidade quanto em duas viscosidades associadas, durante todo o tempo de trabalho. O poliéter mostrou um melhor comportamento no que diz respeito ao escoamento quando comparado ao polivinilsiloxano. (AU)

Good flowable impression materials are needed to capture preparation margins. The aim of this study was to evaluate, through the 'shark-fin' test device (3M ESPE), the flow of two elastomeric impression materials, a polyether (PE) and a polyvinylsiloxane (PVS). The 'shark-fin' test was modified to convey the approximation of the in vitro study to the clinical application, assessing the behavior of two viscosities of each material applied at one point in time. A high viscosity polyether (PE) (Impregum Penta Soft / 3M ESPE) and a low viscosity (Impregum Garant L Duosoft / 3M ESPE), a high viscosity polyvinylsiloxane (PVS) (Express XT Penta H / 3M ESPE), a medium viscosity (Express XT Regular Body / 3M ESPE) and a low viscosity (Express XT Light Body / 3M ESPE) were divided into 21 groups (n=5) and tested solely, and in a layered mixture of 1 : 1 at working times of 50, 80 and 120 s. Afterwards, the fin heights were measured with a digital caliper. The statistical analysis was performed by one-way analysis of variance (ANOVA) and LSD post hoc test (p=0,05). It was found that the 'shark-fin' values differed significantly among materials and at each time interval (p<0,05). The fin heights decreased for all groups with increasing of working time, except for the low viscosity PE and PVS in multiple mixtures (high with low viscosity and high with medium viscosity). The PE groups showed the highest 'shark-fins' compared to PVS, both in single and multiple mixtures, during the entire working time. The polyether impression materials had a better flow profile compared to polyvinylsiloxane groups. (AU)

Antimicrobial and physical properties of alginate impression material incorporated with silver nanoparticles.

BACKGROUND: Self-disinfecting impression materials would reduce time and energy needed for impression disinfecting process in clinic. The aim of this study was to evaluate the antimicrobial effect of alginate mixed with nanosilver solution at a concentration of 500 ppm and 1000 ppm on common oral microorganisms and assess changes in working time, setting time, and surface detail reproduction. MATERIALS AND METHODS: In this in vitro study, three groups were assigned. The first group was alginate, the second group was alginate mixed with 500 ppm nanosilver, and the third group was alginate mixed with 1000 ppm nanosilver. Antimicrobial effect on Escherichia coli, Staphylococcus aureus, and Candida albicans was studied using direct contact test in each group (n = 10). Working time (n = 10), setting time (n = 10), and surface detail reproduction (n = 10) were evaluated separately using the ISO 21563 protocol. Descriptive tables were used to describe the data. Kruskal-Wallis test used to determine significant differences in the number of colonies was counted in antimicrobial test (α = 0.05). RESULTS: No adverse effects observed in working time, setting time, and surface detail reproduction of alginate impressions. Alginate mixed with silver nanoparticles showed no inhibitory effect on S. aureus and C. albicans, but the number of E. coli colonies were counted in the group 1000 ppm was significantly lower than 500 ppm (P = 0.001). CONCLUSION: Antimicrobial effect of alginate mixed with silver nanoparticles is not clinically indicated. Nevertheless, its physical features did not change significantly.

Comparação de Diferentes Técnicas de Moldagem com Silicone de Adição - Estudo in vitro / Comparison of Different Impression Techniques With Addition Silicone - in vitro Study

Objetivo: Comparar diferentes técnicas de moldagem com silicone de adição, quanto à precisão e fidelidade da cópia através de medidas manuais e sobreposição em CAD/CAM. Material e método: Foram realizadas 4 moldagens com silicone de adição de um mesmo modelo nas seguintes técnicas: T1 ­ dois passos com recorte; T2 ­ dois passos com alívio de filme PVC; T3 ­ dois passos sem alívio e T4 - simultânea. A fidelidade das 4 técnicas de moldagem foi avaliada por meio de mensurações de 5 dimensões nos modelos de gesso vazados em cada um dos moldes obtidos. Outra forma de análise foi a sobreposição de imagens no CAD/CAM, com a finalidade de verificar se há semelhanças ou diferenças dimensionais entre o modelo piloto e as amostras. As medidas obtidas foram submetidas ao teste ANOVA com comparações múltiplas pelo teste de Tukey (α=0,05). Resultados: De acordo com as mensurações, a técnica que apresentou maior discordância do modelo piloto foi a T4, não havendo diferença entre as outras técnicas. Na avaliação em CAD/CAM, as técnicas T4 e T3 apresentaram maiores diferenças em relação ao modelo original de acordo com as imagens sobrepostas. Conclusões: Todas as técnicas estudadas apresentaram alterações dimensionais, em especial a técnica simultânea e a sem alívio, tanto nas medidas obtidas quanto na análise em CAD/CAM.

Objetives: To compare different impression techniques with addition silicone, by means of copy accuracy through manual measurements and overlaping in CAD/CAM. Material and methods: Four impressions of a same pilot model were carried out with silicone addition in different techniques: T1 ­ two steps with cut-back; T2 ­ two steps with PVC film relief; T3 ­ two steps without relief; and T4 ­ one step. The accuracy of the 4 different impression techniques was assessed by measuring 5 dimensions on stone casts poured from the impressions of the pilot model. Another analysis was carried out in CAD/CAM using the overlaping of the casts and the pilot model, in order to verify dimensional similarities and differences between them. The values obtained were submitted to ANOVA and Tukey test, for multiple comparisons (α=0.05). Results: According to the measures done, the technique that generated the greatest difference from the pilot model was T4, with no difference among the other techniques. In CAD/CAM analysis, techniques T4 and T3 presented more differences from the original model. Conclusions: All studied techniques presented dimensional changes, mainly the 1 step and the 2 step without relief, in both methods, measures and CAD/CAM analysis.

The use of retraction paste to simplify impression and cementation of ceramic veneers and crowns: 3-year follow-up report.

Proper gingival displacement is an important prerequisite to obtain good quality impressions. Retraction pastes could eliminate the need for retraction cords, as they have advantages such as comfort reported by patients, faster technique, ease of use, no need for anesthesia, and reduced tissue trauma. The objective of this paper was to present a clinical case of ceramic veneers and crowns in which a retraction paste was used for gingival displacement during both the impression and cementation stages, with 3 years of follow-up. Treatment planning consisted of the replacement of preexisting crowns and ceramic veneers on the anterior teeth. After finishing the preparations, gingival displacement with Astringent Retraction Paste was performed without anesthesia or the use of cords and the impression was taken. Before cementation of the crowns and veneers, the Astringent Retraction Paste was applied. Avoiding the use of cords during cementation prevented trauma. The soft tissue margins remained stable and healthy after a period of 3 years. It can be concluded that retraction pastes could be indicated for displacement of soft tissue when preparation margins are at the gingival level or slightly intrasulcular prior to impressions, restoration cementations, direct restorations, and before relining provisional restorations. Clinical significance: The impression appointment can be traumatic to some patients. The use of cords for gingival displacement usually requires local anesthesia and is time consuming. Retraction astringent pastes instead of cords seems to be a good option for some cases in gingival tissue displacement.